Lenco IPD-5200 Specifications download pdf (Page 7)

Eng Eng

Sleep Timer Function

Sleep to timer

This feature allows you to fall asleep to the radio or iPod for up to 120 Minutes.

The unit shuts off automatically when the time expires.

1. Press the POWER button to turn the unit on.

2. Either tune to the desired radio station in radio mode or playback music

from the iPod.

3. To select the sleep timer to turn the unit off after 15, 30, 45, 60, 90 or

120 minutes, press the SLEEP button repeately. The display show the

indicator . The unit plays for the selected length of time then

automatically turns off.

4. To turn the unit off before the sleep timer counts down to zero, press

the POWER button at any time.

Notes :

If you are falling asleep to music from an external device connected to the

AUX input, the sleep timer will shut off the power to this system but it will

not turn off the external device.

Wake to iPod or Radio

When the alarm time is reached, the selected alarm source (iPod or Radio)

will automatically turn on. It starts softly and gradually becomes louder.

It plays for 30 minutes then shuts off and resets itself for the following day.

During the activation of the alarm source, you may press the SNOOZE

button to activate the snooze function. The alarm stops for the snooze time

(around 10 minutes) then turns on again.

To cancel the snooze before it expires, press the ALARM button.

This manual snooze operation can be repeated three times. Each time the

alarm turns on, it plays for 30 minutes (without pressing the snooze button).

To stop the alarm immediately after the alarm sounds, you may also press

the ALARM button. It resets itself for the following day.

Alarm Operation

When the unit is OFF (power off mode):

Select wake up alarm source

1. Press and hold the ALARM button until the alarm source indicator blink.

2. Press the T/CH / button to select alarm source BUZ (buzzer) ,

iPod or RAD (radio).

Setting the alarm time

3. Press the ALARM button again, alarm time digits blink.

4. Press the V / button to set alarm hour.

5. Press the T/CH / button to set alarm minute.

Save settings and activate alarm

6. To save all settings and exit the setting mode, press the SNOOZE button.

7. To activate the daily alarm, press the ALARM button and the

corresponding alarm source indicator appears on the LCD display.

Notes :

---If "Wake to iPod" is selected but your iPod has not been docked, the alarm

source will be redirected to the Alarm Buzzer automatically when the alarm

is reached.

---When "Wake to Radio" is selected, make sure the radio station which you

want to wake to is tuned.

Wake to Buzzer

When the alarm time is reached, the buzzer alarm will sound for 3 Minutes.

It goes into Auto-snooze mode if no further button has been pressed.

The display shows the "SNOOZE" indicator. The buzzer turns off for the

snooze time (around 10 minutes) then comes on again. This operation will

be repeated three times. After the fourth alarm is finished, the alarm will

shut off until the same alarm time on the next day.

You may also activate the snooze function manually after the alarm sounds

by pressing the SNOOZE button. The buzzer stops for the snooze time then

comes again.

To cancel the snooze before it expires, press the ALARM button.

The snooze operation (including auto-snooze and manual snooze) can be

repeated by 3 times only.

To stop the alarm immediately after the buzzer sounds, you can also press

the ALARM button. It resets itself for the following day.

IPD5200 iB.indd EN112-EN113IPD5200 iB.indd EN112-EN113 2010-10-11 8:22:532010-10-11 8:22:53

size:105x146mm,material:80gms book paper,BK+BK

1 2 3 4 5 6 7 8 9 10 11 12 ... 39 40

Comments to this Manuals

No comments

Lenco IPD-5200 Specifications Page 7

Comments to this Manuals